{"id":437667,"date":"2024-10-20T08:00:13","date_gmt":"2024-10-20T08:00:13","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/ieee-2960-2023\/"},"modified":"2024-10-26T15:02:54","modified_gmt":"2024-10-26T15:02:54","slug":"ieee-2960-2023","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/ieee\/ieee-2960-2023\/","title":{"rendered":"IEEE 2960-2023"},"content":{"rendered":"
New IEEE Standard – Active. Stationary Meter Test Units (MTUs) permanently installed in laboratories, used for testing and calibration of direct current electrical energy meters, in particular for their type test, acceptance test, and verification test, are applied to in this guide. The requirements for automatic MTUs and applies to newly manufactured MTUs to test electrical energy meters on direct current systems with a voltage up to 1 500 V is covered. Finally, it should be noted that the entire guide does not contain normative requirements<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | IEEE Std 2960\u2122-2023 Front cover <\/td>\n<\/tr>\n | ||||||
2<\/td>\n | Title page <\/td>\n<\/tr>\n | ||||||
4<\/td>\n | Important Notices and Disclaimers Concerning IEEE Standards Documents <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | Participants <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 1.\u2002Overview 1.1\u2002Scope 1.2\u2002Purpose 1.3\u2002Word usage <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 2.\u2002Normative references 3.\u2002Definitions, acronyms, and abbreviations 3.1\u2002Definitions <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 3.2\u2002Acronyms and abbreviations <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 4.\u2002MTU and methods of testing DUT 4.1\u2002MTU 4.2\u2002Methods of testing DUT <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 5.\u2002Electrical values and requirements 5.1\u2002Mains supply 5.2\u2002The requirements of measurement performance of the complete MTU <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 5.3\u2002Output values and ranges of the test circuits <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 5.4\u2002Error calculation system <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 5.5\u2002Maximum permissible error requirements for the working standard 6.\u2002Construction and insulation requirements of MTU 6.1\u2002Construction requirements <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | 6.2\u2002Insulation requirements <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | 7.\u2002Marking requirements 7.1\u2002General <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | 7.2\u2002Labels, signs, and signals 7.3\u2002Other information 8.\u2002Climatic conditions for MTU 8.1\u2002Normal environmental conditions <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | 8.2\u2002Extreme environmental conditions 8.3\u2002Temperature limits 9.\u2002Electromagnetic compatibility <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | 10.\u2002Test methods of electrical values and requirements 10.1\u2002Test conditions 10.2\u2002Conformity inspection by visual inspection 10.3\u2002Error test <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | 10.4\u2002Repeatability of the measurements 10.5\u2002Output stability of power <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | 10.6\u2002Short-term stability 10.7\u2002Consistency of multiple output 10.8\u2002RMSR of the current and voltage circuits 10.9\u2002Error of the working standard 11.\u2002Test items <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | 11.1\u2002Type tests 11.2\u2002Acceptance tests 11.3\u2002Verification tests <\/td>\n<\/tr>\n | ||||||
31<\/td>\n | Back cover <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Guide for Testing Equipment for Direct Current Electrical Energy Meters (Approved Draft)<\/b><\/p>\n |