{"id":72974,"date":"2024-10-17T16:27:22","date_gmt":"2024-10-17T16:27:22","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/awwa-e102-2006-with-erratum-2010\/"},"modified":"2024-10-24T19:08:40","modified_gmt":"2024-10-24T19:08:40","slug":"awwa-e102-2006-with-erratum-2010","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/awwa\/awwa-e102-2006-with-erratum-2010\/","title":{"rendered":"AWWA E102 2006 With Erratum 2010"},"content":{"rendered":"
This standard describes minimum requirements for submersible vertical turbine pumps utilizing a discharge column pipe assembly, 5 hp or larger, used in water service, including materials, design, manufacture, inspection, and testing.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | Erratum to ANSI\/AWWA E102-06 Standard \n <\/td>\n<\/tr>\n | ||||||
3<\/td>\n | ANSI\/AWWA E102-06 <\/td>\n<\/tr>\n | ||||||
5<\/td>\n | Committee Personnel <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | Foreword I. Introduction. <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | II. Special Issues. III. Use of This Standard. <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | IV. Comments. <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | AWWA Standard Submersible Vertical Turbine Pumps \n SECTION 1: GENERAL Sec. 1.1 Scope Sec. 1.2 Purpose Sec. 1.3 Application <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | SECTION 2: REFERENCES <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | SECTION 3: DEFINITIONS <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | SECTION 4: REQUIREMENTS Sec. 4.1 Standard Nomenclature Sec. 4.2 Data Form Sec. 4.3 Inspection and Certification by Manufacturer Sec. 4.4 Information to Be Supplied by Manufacturer Sec. 4.5 Materials and Sanitary Codes <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | Table 1 Standard nomenclature\u2014submersible vertical turbine pumps <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | Table 1 Standard nomenclature\u2014submersible vertical turbine pumps (continued) <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | Table 1 Standard nomenclature\u2014submersible vertical turbine pumps (continued) <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | Table 1 Standard nomenclature\u2014submersible vertical turbine pumps (continued) <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | Sec. 4.6 Submersible Motor <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | Sec. 4.7 Submersible Cable <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | Sec. 4.8 Surface Plate Sec. 4.9 Strainer Sec. 4.10 Discharge Pipe <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | Table 2 Diameters and weights of standard discharge column pipe sizes Sec. 4.11 Pump Bowls Sec. 4.12 Bowl Bearings Sec. 4.13 Impellers <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | Sec. 4.14 Wear Rings Sec. 4.15 Shaft <\/td>\n<\/tr>\n | ||||||
31<\/td>\n | Sec. 4.16 Pump Motor Coupling Sec. 4.17 Protective Coatings SECTION 5: VERIFICATION Sec. 5.1 Inspection Sec. 5.2 Factory Performance Testing <\/td>\n<\/tr>\n | ||||||
32<\/td>\n | Sec. 5.3 Performance Test Sec. 5.4 Typical Laboratory Test Arrangement <\/td>\n<\/tr>\n | ||||||
33<\/td>\n | Sec. 5.5 Capacity Measurement <\/td>\n<\/tr>\n | ||||||
34<\/td>\n | Sec. 5.6 Head Measurement Sec. 5.7 Velocity Head Sec. 5.8 Power Input to Pump Motor <\/td>\n<\/tr>\n | ||||||
35<\/td>\n | Sec. 5.9 Hydrostatic Tests Sec. 5.10 Recording and Computation of Test Results SECTION 6: DELIVERY Sec. 6.1 Marking <\/td>\n<\/tr>\n | ||||||
36<\/td>\n | Sec. 6.2 Preparation for Shipment Sec. 6.3 Affidavit of Compliance <\/td>\n<\/tr>\n | ||||||
37<\/td>\n | APPENDIX A Submersible Vertical Turbine Pump Data Form \n <\/td>\n<\/tr>\n | ||||||
39<\/td>\n | APPENDIX B Engineering Data \n SECTION B.1: DISCHARGE COLUMN PIPE SECTION B.2: FRICTION LOSS SECTION B.3: DISCHARGE-ELBOW HEAD LOSS <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" AWWA E102-06: Submersible Veritcal Turbine Pumps With Erratum-201001<\/b><\/p>\n |