This standard applies to external fuses used with high-voltage capacitors according to IEC 60871-1, Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V \u2013 Part 1: General. IEC 60871-1 is applicable to both capacitor units and capacitor banks intended to be used, particularly, for power-factor correction of a.c. power systems, and also to capacitors intended for use in power filter circuits.<\/p>\n
Fuses according to this standard are intended to clear either faults inside a capacitor unit to permit continued operation of the remaining parts of the bank in which the unit is connected (unit fuses) or faults on the whole capacitor bank to isolate the bank from the system (line fuses).<\/p>\n
In this standard the terms \u201ccapacitive current\u201d and \u201cinductive current\u201d are used to indicate test currents that have a leading or lagging power factor, respectively, and in which the circuit contains predominantly capacitive or inductive components. The word “capacitor” is used when it is not necessary to lay particular stress upon the different meanings of the word “capacitor unit” or “capacitor bank”.<\/p>\n
In some cases, fuses tested only to IEC 60282-1 or IEC 60282-2 may be suitable for use with capacitors if they are not required to interrupt capacitive currents (e.g. if capacitive currents cannot flow, or if they are acting as a \u201cback-up\u201d, to provide high inductive current breaking, to other devices that will clear capacitive currents).<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 6<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 4 Performance requirements 4.1 General 4.2 Breaking requirements 4.2.1 Rated maximum capacitive breaking current 4.2.2 Rated capacitor discharge energy <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 5 Type tests 5.1 General 5.2 Test practices 5.3 Power frequency inductive current tests Table 1 \u2013 Type tests required <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 5.4 Capacitive breaking current tests 5.4.1 Description of tests to be made 5.4.2 Test circuits <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 5.4.3 Arrangement of the equipment <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 5.4.4 Test procedure Figure 1 \u2013 Test circuit for test duty A Figure 2 \u2013 Test circuit for test duty B <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 5.4.5 Parameters to be used for tests 5.4.6 Test It for fuse-links that exhibit take-over current(s) Table 2 \u2013 Capacitive current breaking tests <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 5.5 Capacitor Discharge breaking tests 5.5.1 General 5.5.2 Test circuit <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 5.5.3 Test procedure 5.6 Standard conditions of behaviour with respect to breaking tests 6 Information to be given to the user 7 Application information 7.1 Operating voltages <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 7.2 Rated voltage 7.3 Rated current <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Bibliography Figures Tables <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" High-voltage fuses for the external protection of shunt capacitors<\/b><\/p>\n |