ISO 7375-1:1986
$13.00
Road vehicles — Coiled pipe assemblies for pneumatic braking connection between motor vehicles and towed vehicles — Part 1: Dimensions
| Published By | Publication Date | Number of Pages |
| ISO | 1986-11 | 4 |
Specifies the minimum conditions to ensure braking compatibility and in particular response time for coiled pipe assemblies. Applies to coiled pipe assemblies for vehicle combinations equipped with pneumatic braking systems. Does not apply to other thermo-plastics tubing used in such braking systems. This second edition cancels and replaces the first edition (1982).
Related products
-
BS 4317-17:1987
Methods of test for cereals and pulses – Determination of fat acidity Published By Publication…
-
BS 6578-2:1985
Laryngoscopic fittings – Specification for screw threads for miniature electric lamps and sockets Published By…
-
BS 6636-2:1987
Message types for securities – Specification for messages for orders to buy/sell Published By Publication…
-
BS EN ISO 4375:2004
Hydrometric determinations. Cableway systems for stream gauging Published By Publication Date Number of Pages BSI…
-
BS 5763-0:1986
Methods for microbiological examination of food and animal feeding stuffs – General laboratory practices Published…
-
BS ISO/IEC 2022:1994:1995 Edition
Information technology. Character code structure and extension techniques Published By Publication Date Number of Pages…
-
BS EN ISO 3549:2002 2003
Zinc dust pigments for paints. Specifications and test methods Published By Publication Date Number of…
-
ISO 7875-1:1996
Qualité de l’eau — Dosage des agents de surface — Partie 1: Dosage des agents…
-
BS AU 138b:2000
Towing vehicle, trailer and semi-trailer pneumatic braking systems. “Contact” type couplings Published By Publication Date…
-
BS 7371-8:2011
Coatings on metal fasteners – Specification for sherardized coatings Published By Publication Date Number of…
-
BS 7020-3:1988:1989 Edition
Analysis of iron ores – Method for the determination of combined water content Published By…
-
BS ISO 3775:1990:1996 Edition
Cinematography. Printed 8 mm Type S image area on 16 mm motion-picture film perforated 8…
-
BS AU 205:1986
Method of test for effect of braking on steady state cornering behaviour of road vehicles…
-
BS 7372-2:1991
Guide to the choice of aperture size and wire diameter combinations for industrial wire screens…
-
BS 7325:1990
Method for determination of the compressive strength of paper and board by the short span…
-
BS EN 737-2:1998:2000 Edition
Medical gas pipeline systems – Anaesthetic gas scavenging disposal systems. Basic requirements Published By Publication…
-
JIS B 1008:2009
Fasteners – Bolts and studs – Split pin holes and wire holes Published By Publication…
-
BS EN 27372:1992
Trade data interchange. Trade data elements directory Published By Publication Date Number of Pages BSI…
-
BS 6487:1984
Specification for split pin holes and wire holes in bolts, screws and studs Published By…
-
CAN/CSA-ISO/IEC 2022-96:2000 Edition
Information Technology – Character Code Structure and Extension Techniques Published By Publication Date Number of…
-
ISO 6702-2:1991
Aircraft — Requirements for on-board weight and balance systems — Part 2: Design, performance and…
-
BS EN ISO 15502:2005:2008 Edition
Household refrigerating appliances. Characteristics and test methods Published By Publication Date Number of Pages BSI…
-
BS 5375:1976
Methods of test for raw general purpose chloroprene rubbers Published By Publication Date Number of…
-
BS 6068-2.24:1986
Water quality. Physical, chemical and biochemical methods – Method for the determination of non-ionic surfactants…
-
BS EN ISO 7345:1996
Thermal insulation. Physical quantities and definitions Published By Publication Date Number of Pages BSI 1996…
-
BS ISO 7975:2006 2008
Passenger cars. Braking in a turn. Open-loop test method Published By Publication Date Number of…
-
BS 5375:1992
Method for evaluation of general purpose chloroprene rubber (CR) Published By Publication Date Number of…
-
BS 4427-15:1982
Methods of test for sodium tripolyphosphate (pentasodium triphosphate) and sodium pyrophosphate (tetrasodium pyrophosphate) for industrial…
-
BS EN ISO 7345:2018
Thermal performance of buildings and building components. Physical quantities and definitions Published By Publication Date…
-
BS 6578-1:1985
Laryngoscopic fittings – Specification for hook-on type handle-blade fittings Published By Publication Date Number of…
-
BS 7345:1990
Specification for nominal lengths of bolts, screws and studs and thread lengths for general purpose…
-
BS 7715:1994
Specification for prevailing torque type bolts, screws and studs with non-metallic prevailing torque elements incorporated…
-
BS 4361-27:1990
Woodworking machines – Nomenclature for disc sanding machines with spindle in fixed position Published By…
-
BS 6759-1:1984
Safety valves – Specification for safety valves for steam and hot water Published By Publication…
-
BS 1753:1987
Specification for safety requirements for children’s cots for domestic use Published By Publication Date Number…
-
BS 7372-1:1991
Guide to the choice of aperture size and wire diameter combinations for industrial wire screens…
-
BS ISO 7775:1991:1992 Edition
Securities. Scheme for message types Published By Publication Date Number of Pages BSI 1992 60
-
BS 6636-1:1985
Message types for securities – Specification for messages for receipt/delivery Published By Publication Date Number…
-
BS 6043-2.1:1985
Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrode coke –…
-
BS 6068-2-2.23:1986
Water quality. Physical, chemical and biochemical methods – Method for the determination of anionic surfactants…