BS EN 13361:2013
$189.07
Geosynthetic barriers. Characteristics required for use in the construction of reservoirs and dams
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 46 |
This European Standard specifies the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, to be used as fluid barriers for potable, fresh or saline water, in the construction of reservoirs and dams, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of water through the construction.
This European Standard is not applicable to geotextiles or geotextile-related products.
This European Standard provides for the evaluation of conformity of the product to this document.
This European Standard defines requirements to be met by manufacturers and their authorised representatives with regard to the presentation of product properties.
This European Standard does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption.
Where potable water is or may be in direct contact with the product the designer should also refer to other relevant standards, requirements and/or regulations.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 8 | 1 Scope 2 Normative references |
| 10 | 3 Terms, definitions and abbreviations 3.1 Terms and definitions |
| 11 | 3.2 Abbreviations 4 Required characteristics and corresponding methods of test 4.1 General 4.2 Types of application 4.2.1 General 4.2.2 Application 1: “covered in service” |
| 14 | 4.2.3 Application 2: “not covered in service” |
| 15 | 4.3 Relevant characteristics |
| 20 | 4.4 Characteristics relevant to specific conditions of use 4.4.1 General 4.4.2 Tear strength 4.4.3 Burst strength 4.4.4 Friction characteristics (direct shear and inclined plane tests). 4.4.5 Low temperature behaviour 4.4.6 Weathering |
| 21 | 4.4.7 Resistance to wetting and drying 4.4.8 Freeze-thaw cycle resistance 4.4.9 Resistance to root penetration 4.4.10 Chemical resistance 4.5 Release of dangerous substances 5 Evaluation of conformity 5.1 Presentation of characteristics 5.2 Verification of values |
| 22 | 5.3 Initial type tests 5.4 Factory production control |
| 23 | 5.5 Inspection 6 Marking |
| 24 | Annex A (normative) Factory production control — Factory production control scheme A.1 General A.2 Product design A.3 Production A.3.1 Raw or incoming materials A.3.2 Production process A.4 Finished products A.4.1 Raw or incoming materials |
| 27 | A.4.2 Alternative tests A.4.3 Equipment |
| 28 | A.4.4 Provisions applicable to A.2, A.3 and A.4 (to be used where appropriate) A.4.4.1 Records A.4.4.2 Assessment of results A.4.4.3 Traceability A.4.4.4 Corrective action for non-conforming materials and products A.4.4.5 Personnel A.4.4.6 Quality management |
| 29 | Annex B (normative) Durability of geosynthetic barriers B.1 Introduction B.1.1 Standards to which this annex is common B.1.2 Mechanisms of degradation |
| 30 | B.1.3 Service life B.1.4 Use of rework materials B.2 Test requirements B.2.1 General requirement B.2.2 Requirements for repeat testing |
| 31 | B.2.3 Requirements for individual materials B.2.3.1 Polyolefins B.2.3.2 Thermoset elastomers B.2.3.3 Coated Fabrics |
| 32 | B.2.3.4 PVC-P B.2.3.5 Clay geosynthetic barriers (GBR-C) B.2.3.6 Bituminous geosynthetic barriers (GBR-B) B.3 Durability tests B.3.1 Introduction B.3.2 Weathering B.3.2.1 General |
| 33 | B.3.2.2 Direct tests and accelerated tests B.3.2.3 Period of exposure |
| 34 | B.3.2.4 Requirements for periods of exposure up to one year B.3.2.5 Periods of exposure greater than one year B.3.3 Resistance to micro-organisms B.3.4 Resistance to environmental stress cracking B.3.5 Resistance to leaching |
| 35 | B.3.6 Resistance to oxidation B.3.7 Chemical resistance B.3.7.1 All applications B.3.7.2 Liquid and solid waste storage (EN 13492 and EN 13493) B.4 Evaluation tests and acceptance criteria B.4.1 General B.4.2 Evaluation by comparison of tensile properties |
| 36 | B.4.3 Evaluation by comparison of Oxidative Induction Time (OIT) values B.4.4 Evaluation by change in mass B.4.5 Evaluation by change in water permeability |
| 37 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive ZA.1 Scope and relevant characteristics |
| 38 | ZA.2 Procedure for attestation of conformity of geosynthetic barriers |
| 40 | ZA.3 CE marking and labelling |
