AWWA D120 2009
$75.83
AWWA D120-09: Thermosetting Fiberglass Reinforced Plastic Tanks
| Published By | Publication Date | Number of Pages |
| AWWA | 2009 | 48 |
This standard covers the composition, performance requirements, construction practices and workmanship, design, and methods of testing thermosetting fiberglass-reinforced plastic tanks for the storage of water and other liquids.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | ANSI/AWWA D120-09 |
| 3 | Committee Personnel |
| 5 | Contents |
| 7 | Foreword I. Introduction. |
| 10 | II. Special Issues. III. Use of This Standard. |
| 11 | IV. Major Revisions. V. Comments. |
| 13 | AWWA Standard Thermosetting Fiberglass-Reinforced Plastic Tanks SECTION 1: GENERAL Sec. 1.1 Scope |
| 14 | Sec. 1.2 Purpose Sec. 1.3 Application SECTION 2: REFERENCES |
| 16 | SECTION 3: DEFINITIONS |
| 17 | SECTION 4: REQUIREMENTS Sec. 4.1 Classification Sec. 4.2 Potable Water Service Sec. 4.3 Materials |
| 18 | Sec. 4.4 General Requirements |
| 19 | Table 1 Design loads Sec. 4.5 Design |
| 20 | Sec. 4.6 Physical and Mechanical Properties of Tank Shell |
| 21 | Sec. 4.7 Environmental Resistance of Tank Shell Sec. 4.8 Leakage Under Internal Pressure Sec. 4.9 Additional Requirements for Underground Tanks Sec. 4.10 Construction |
| 23 | Table 2 Minimum widths of overlaid joints (exclusive of taper) |
| 26 | Table 3 Pipe for nozzle assembly Table 4 Minimum flange thickness for FRP nozzles |
| 28 | Table 5 Shear-bond area—nozzles |
| 29 | SECTION 5: VERIFICATION Sec. 5.1 General |
| 30 | Sec. 5.2 Production Tests |
| 31 | Sec. 5.3 Physical and Mechanical Properties of Tank Shell |
| 32 | Sec. 5.4 Environmental Resistance |
| 33 | Sec. 5.5 Additional Tests for Underground Tanks |
| 34 | Table 6 Torques on pipe fittings |
| 35 | Sec. 5.6 Aboveground-Tank Surface Burning Characteristics Sec. 5.7 Retest Sec. 5.8 Inspection and Testing by Purchaser |
| 36 | SECTION 6: DELIVERY Sec. 6.1 Marking Sec. 6.2 Packaging and Shipping |
| 37 | Sec. 6.3 Handling Sec. 6.4 Installation |
| 38 | Sec. 6.5 Affidavit of Compliance |
| 39 | APPENDIX A Explanatory Notes to D120 |
| 41 | APPENDIX B Pre-installation Site Analysis for Underground Tanks SECTION B.1: GENERAL SECTION B.2: TANK ANCHORAGE |
| 42 | SECTION B.3: PERMEATION |
| 43 | APPENDIX C Accessories for Underground Tanks SECTION C.1: SHELL MANWAY SECTION C.2: SHELL MANWAY EXTENSIONS SECTION C.3: MANWAY RISER PIPE SECTION C.4: STEEL NPT FITTINGS |
| 44 | SECTION C.5: TANK LADDERS SECTION C.6: ANCHOR STRAPS SECTION C.7: TURBINE ENCLOSURES SECTION C.8: MANWAY COVERS SECTION C.9: CONNECTION HARDWARE |
| 45 | APPENDIX D Flanged-Joint Bolts, Gaskets, and Installation SECTION D.1: BOLTS AND NUTS SECTION D.2: GASKETS |
| 46 | SECTION D.3: INSTALLATION |
